跳至正文

Packaging MAP on a VFFS: Nitrogen, CO₂, and Oxygen in the Right Proportions

MAP stands for modified atmosphere packaging: the air in the bag is replaced with a gas mixture that extends the product’s shelf life. This guide covers the three gases and how they work, the purging methods used on the VFFS, the film requirements, and the realistic residual levels—for coffee, snacks, cheese, and meat.

Table of Contents

MAP packaging starts with a simple observation: spoilage is fueled by oxygen, and half of the air in a bag is oxygen. MAP—modified atmosphere packaging—replaces that air with a gas mixture suited to the product. On a vertical form, fill, and seal machine This is done on the production line: rinsing during filling, sealing under gas. This guide explains what each gas does and how to use them.

The Three Gases and Their Work

Nitrogen (N₂) It’s the workhorse: inert, flavorless, and inexpensive. It displaces oxygen and fills the bag so the product doesn’t touch the sides. Nitrogen doesn’t actively protect but neutralizes—the foundation of every coffee and snack package.

Carbon dioxide (CO₂) Has a bacteriostatic effect: it dissolves in the product’s moisture and lowers the pH, which microorganisms rely on for survival. Cheese, fried snacks, and deli meats require CO₂ levels ranging from 30 to 60%. The downside: CO₂ dissolves slowly in fat, so the bag shrinks slightly in the days following sealing.

Oxygen (O₂) It sounds wrong, but it’s essential for red meat: the red blush requires 70 to 80% O₂ with residual CO₂. This is the only standard application where oxygen remains inside—for everything else, it’s out.

Gas How It Works Typical share Product
Nitrogen inert, fills 70 to 100% coffee, snacks, powdered milk
Carbon dioxide antibacterial 30 to 60% cheese, deli meats, fried foods
Oxygen color retention 70 to 80% red meat
MAP mixture low in oxygen residual O₂ below 2% most products

Winding on the VFFS: Two Methods

The first method is rinse: a spray tube that blows air into the formed pouch as the air flows out—simple, with residual oxygen between 1 and 2%. The second is vacuuming and backwashing: The bag is first evacuated and then filled with the mixture, which reduces the residual oxygen to below 1% but extends the cycle time. A complete comparison of the two approaches can be found at vacuum packaging or nitrogen packaging; the machine side describes Choosing a Vacuum Sealer.

Film and Residual Content

MAP uses only film that traps gases: a barrier layer with an oxygen transmission rate of less than 1 cm³ per m² per day for products with a long shelf life. A single-material film without a barrier will allow the mixture to leak out within weeks—the choice of film is described in detail at Choosing Film for a VFFS. Measure the residual oxygen on a regular basis: immediately after sealing, after one week, and after transport, so you can determine whether any deviations are due to the rinse water or the film.

Where MAP Delivers the Most Value

Coffee retains its aroma 2 to 3 months longer when stored under nitrogen; snacks stay crispy as long as moisture doesn't get in; cheese and deli meats gain days to weeks of shelf life with CO₂. For coffee production, the complete production line setup is available at coffee packaging machine. And for products where MAP isn't effective—dry goods that are already stable—it's simply an unnecessary expense: first determine whether your shelf-life issue is actually caused by oxygen.

Frequently Asked Questions

Q: How much does MAP cost per bag in terms of gas?

Gas is the smallest cost item per bag: the mixer and the rinsing unit represent the investment, while consumption is determined by the bag volume. Calculate the business case based on the combined costs of film and the machine, not on gas alone—the same approach as with How much does a packaging machine cost?.

Q: Can I use my existing VFFS MAP with this?

This is often the case: rinse tubes and gas connections can be installed as options on machines that are designed for them, and the mixer is located right next to them. The question is whether the control system can schedule the rinse time into the cycle without losing speed—have this calculated based on your target speed.

Q: How do I check the mixture?

Using a gas analyzer that pierces the film: take hourly samples to measure temperature, concentration, and residual oxygen. Log the values for each batch—in the event of a complaint or audit, the log serves as proof that your atmosphere was correct, in addition to the readings from your checkweigher, as in Combine checkweighers.

Related pages

vertical form, fill, and seal machine | coffee packaging machine | vacuum packaging or nitrogen packaging | Choosing Film for a VFFS | Choosing a Vacuum Sealer


Request a technical proposal Please specify the product, bag size, and desired output.

Picture of Evelien

Evelien

I am an expert with 16 years of experience and have completed more than 300 projects. My goal is to provide you with the most suitable packaging solution right away.

Sign up for our newsletter

We select the most popular case studies from more than 4,000 orders placed by our customers and help you find your winning project.